Enlargement accessories are the small parts that get a session started and keep it going. Twenty-three of them sit here, all made for TurboMale systems, and most fit other brands by size.

Five sleeve types and a set of all five, the cup and the protector cap handle the seal. A cushion and two pump seals handle the base.

Springs, rods, a cylinder and a gauge pump add load. Three straps give the grip a new direction, and a hand pump and a hose set wait as spares. Nothing needs tools or adapters, and a size that misses is swapped inside 60 days.

Seal It First. Sleeves, Cups And The Protector Cap

Every vacuum grip holds its pressure through one part, the sleeve. The TurboMale Silicone Sleeve is seamless US platinum silicone, and a single one lasts for years.

The slim bore is for below-average girth, and the set puts all five types in one order. The 6 in and 9 in versions hold the shaft extended once the device comes off. The night sleeve widens at the top, so nothing presses at the cap edge while you sleep.

The sleeve cuffs the TurboMale Vacuum Chamber: German polycarbonate, three sizes, 99% of men covered. Under it sits the protector cap, a soft layer between the glans and the vacuum. Chafed skin and the post-pump donut ring stop at that layer.

Why Sessions Stop Early, And The Three Parts That Fix The Base

A sore base and a rim digging in end sessions early. The TurboMale Extender Cushion sits between the extender base and the pubic bone. The pressure point goes away.

A pump cylinder takes one of two seals. The plain donut seals four cylinder sizes, stops the rim pressing in and adds a light clamp.

The TurboMale Premium Silicone Pump Seal adds a cuff at the base. Nothing outside the cylinder gets pulled in as pressure climbs. It clamps harder than the plain seal, and the patent-pending design exists in no other catalog.

Springs, Rods And A Wider Cylinder When The Tape Stops

Most plateaus come down to load or reach, and each has a part. The third cause, an untrained direction, is covered below.

The TurboMale Power Springs 22 lb double a Light Extender's stock pull. Gold owners keep a set as matched spares. Any extender on 8 or 9 mm rods takes them.

The TurboMale Replacement Rods add 10 in (25 cm) of reach to a Light or a Gold. Steps run down to 0.4 in (1 cm) on aviation-grade duralumin, plated in 24K gold or 925 silver. Men with a 20 in (50 cm) target run this set.

When girth outgrows the tube, move up one diameter. The polycarbonate cylinder comes in four inside diameters, with 5 mm walls and a 3-year warranty. The brass gauge pump behind it hits working vacuum by the second stroke.

Three Straps, One Grip, Six Pull Directions

One vacuum grip opens every stretcher direction we make. The TurboMale Complete Tension Bands Set brings all three straps.

The waist belt carries up to 17 lb (8 kg) sideways or straight. The knee band pulls down. The shoulder harness loads the tunica at up to 8.8 lb (4 kg).

The TurboMale Vacuum Platform puts a vacuum grip on rod extenders of any brand. The rods have to be 8 or 9 mm. It seats in one motion, and the cap and sleeve from your kit do the rest.

After pumping or clamping, the TurboMale Erect Rings Set holds the gain the session just put on. Three silicone rings, S, M and L, and they double as a girth device.

A Spare Pump Or Hose Means No Missed Evening

• The TurboMale Vacuum Handle, the compact pump every TurboMale vacuum grip runs on. Sealing takes seconds on any of them
• The TurboMale Hose and Hook Set: 40 in (1 m) of tubing for drawing vacuum without a pump. The hook is rated for 50 lb (23 kg) of plates on any TurboMale cap

No system yet? Start with penis extenders, penis pumps or penis stretchers, and come back here to build it out.

Enlargement Accessories, Matched To Your Symptom

• The seal creeps or the head slips out. A fresh sleeve, or the slim bore when the standard one sits loose
• The base hurts before the session is done. The extender cushion, or a pump seal on the cylinder
• Blisters, chafing, a swollen ring after pumping. The protector cap
• The tape hasn't moved in a month. Power Springs, longer rods, or a strap in a direction you haven't trained
• A pump or a hose went missing. The handle or the hose set, and training continues the same evening

What Separates Our Enlargement Accessories From A Copy

Our silicone leaves the mold with no seam at all, and no other maker has matched that. Copies carry a casting line, and they split along it. The rubber in them smells and irritates skin.

The cups and cylinders are German polycarbonate, the rods duralumin with our own thread. Cups, cylinders, rods, springs, straps and every sleeve are made in the EU, most finished by hand. The straps have no Chinese parts in them.

The practitioners who built the systems build the parts. Fifteen years at the bench, and 7,000 men training on what leaves it. Ask how to fit a new part and the answer is free.

Every session that stops at minute ten builds nothing, so order the enlargement accessories your setup needs. You pay no shipping, the carton stays blank, and a wrong size is exchanged within 60 days.